Please select a business area and your country and language.
December 17, 2019
Has your pneumatic impact wrench started to become unreliable, not perform as it should or suddenly stopped working? One of the most common reasons for lack of durability and premature tool failure is inadequate lubrication – and not just of the motor, but also the impact mechanism.
It’s well known that regular maintenance is vital to make sure your tool is performing at its best. In the same way that you keep the oil levels topped up in your car, it’s important to regularly check the oil and grease in your tool. A little maintenance can go a long way towards improving its durability and longevity. In this blog we’ll look at the two different areas for lubrication and explain how you can maintain your impact wrench properly to ensure that it keeps delivering excellent performance over a long lifetime. We’ll also discuss how often you should lubricate your air tools, and what type of oil you should use so you can make sure you’re working as productively as possible.
When it comes to lubrication, there are two parts of the wrench to consider: a. The motor b. The impact mechanism
The two parts of an impact wrench that need lubricating: the motor and the impact mechanism.
You may be aware that the motor needs regular lubrication, but did you know that the impact mechanism needs lubrication too? Both systems are independent from one another, and therefore must be lubricated separately. The motor is lubricated by a specific airline lubricator that you add in the FRL or directly at the air inlet (at the tool). Whereas the impact mechanism is lubricated in one of two ways depending on the system the tool uses. These are:
Lubricating the impact mechanism is vital to minimize the friction between the impact contact points of the anvil and hammer, and therefore keeps the wrench running in excellent condition. Let’s look at these two systems in greater detail:
Impact mechanism with grease lubrication
In this system grease is applied only on the contact points between the anvil and hammer to prevent friction between them.
An impact wrench mechanism with a grease system needs regular grease replenishment.
Impact mechanism with oil lubrication
In a tool which uses oil bath system, the entire front part of the impact wrench is submerged in oil. There is no question as to whether the oil is present or not, because it surrounds the whole system. One advantage is that lubrication is always present on the contact points, and therefore it requires less maintenance. Maintenance can be trickier, but, with the right tips and pieces of advice, it become very easy to do – as outlined below.
To lubricate the impact mechanism properly, we recommend you open the tool and add grease carefully with your hands or a brush on the critical contact points: the anvil (area in contact with hammer) and in the hammer’s inner area. Most pneumatic tools have multiple grease fittings, and if it isn’t possible to lubricate the impact mechanism as described above, it is sometimes possible to add grease through these holes. If you aren't sure where they are, check your manual or ask your service provided. Don’t forget to remove the old grease before adding the new one!
| Tool operating conditions: | Tool frequency of use : low | Tool frequency of use: high |
| Low | Around 6 months | Around 3 months |
| High | Around 3 months | Around 1 month |
To change the oil, you have to open the tool carefully, drain the used oil and dispose of it appropriately, and then replace it with a new oil. It is imperative that you use oil, which is only suitable for impact systems, for example oil type SAE30. Note: this is different oil from oil used in air lubrication.
| Tool operating conditions: | Tool frequency of use : low | Tool frequency of use: high |
| Low | Around 12months | Around 6 months |
| High | Around 6 months | Around 2 months |
The frequency at which lubrication checks should be carried out depends on your usage and maintenance schedule, and we recommend following manufacturers’ advice here.
Note: regardless of the lubrication type, only use cleaners and grease that have been recommended by the manufacturer. Double check with the tool manual or your service provider if you are not sure.
If the lubrication is applied correctly and frequently, the durability of a tool with a grease mechanism and an oil batch mechanism will be very similar. However, most of the time, grease is not added often enough, and the impact mechanism durability decreases considerably. An impact wrench that has not been lubricated properly will operate with a lower power output, and if the tool is continually used when starved of grease, the internal components will wear down and the tool will not last nearly as long as it could.
Improve the durability of your air tool by regularly lubricating the motor and impact mechanism.
November 9, 2022
Torque Wrenches Oil, gas & petrochemical Tools Maintenance
Torque wrenches are essential power tools for high torque bolting and assembly applications across oil and gas, renewable, and heavy vehicle industries. When it comes to choosing between an electric or hydraulic torque wrench,...
August 24, 2020
Impact Wrenches Tools Safety Metalworking Expert Corner
Thanks to its relatively low cost and robust composition, steel continues to rival alternative materials in applications where cost-efficiency is more important than achieving the lowest possible weight. However, with a density of 7.85 g/cm3, it...
June 1, 2020
Tools Expert Corner Impact Wrenches
With many different options on the market, it can be challenging to know what features to look out for when selecting an impact wrench. This guide provides a brief overview of the technology and outlines some simple steps to help you get starte...
What gives power to your impact wrench?
Join our mailing list
We love hearing from you! Please send us your questions, feedback or topic suggestions. Your submissions are greatly appreciated.
